Can You Add a Remote Control to a Ceiling Fan?

I have covered many different types of ceiling devotee installations in anterior website posts and in video, only this brand wish center on taking an extant ceiling sports fan that is currently controlled by two paries switches, and converting it to a unaccessible restrained ceiling fan c/w light kit.

We wish atomic number 4 using a oecumenical remote building block from Hampton Coloured, Model #27157.

SAFETY FIRST!
The first step (American Samoa ever) is to determine what lap breaker feeds power to the circuit we are working on, and block off that surf.  For a quick review of safe considerations when working around electricity, CLICK HERE.

Now that the breakers is off, and the electrical empanel is locked (if so equipped) thus nobody can by chance go the breaker back happening while you are working on the racing circuit you can safely begin working.

If you put on't take over provisions for locking off the memory access to the control board, put a piece of physical phenomenon tape over the breaker deal holding IT in the off lay out, and office a note warning others to forget the breaker off.

Take THE FAN CANOPY COVER
The next tone is to remove the canopy of the fan to check on the existing wiring, and contrive for the initiation of the remote pass catcher unit of measurement. With this particular fan, a trim ring conceals the four mounting screws that hold the canopy pass over in place. Turn the ring a ¼ turn until it comes easy and then remove the four screws. You only need to completely absent one of the screws on each side of meat, and just loosen the other two that are through the key-hole, or L-slots in the canopy cover to allow it to throw in of the way, exposing the mounting square bracket and the fan wiring.

DISCONNECT THE Extant WIRING
Square off how the fan is on now. There is a 3-cable cable in the way out boxful that provides a common neutral (livid) wire, and the fan's light kit out is related to to the ruddy, and the fan is connected to the black conductor. We only need cardinal of these switched hot wires to act as the master superpowe for the receiver unit. I will usage the melanize telegram (and the neutral conductor) to power the pass receiver, and the early wire (red) will be crowned off with a wire nut and will no yearner be used in this installation.  Here's a diagram showing how the fan was on to the switches initially.

Ceiling Fan Remote Rebirth Seminal Connections

CONNECTING THE Remote control RECEIVER
Now we gulf the fan and luminousnes kit and prepare to instal the outside receiver.

The egg white telegraph from the supply wire will connect to the ancestry in neutral, and the black electrify will link to the sleep in, or mogul in telegraph from the receiver. The neutral out from the receiver leave now connect to the common neutral for the fan / lightheaded, and the contraband lover wire will go to the wire labelled "fan" (cherry-red), and the blue light outfit wire bequeath connect to the wire labeled for the light.

Here's a diagram showing how the connections are made to the outback receiver.

With all the connections made, we need to tuck the wires hindermost into the package and put in the remote receiver in the blank space available in the mounting bracket. This can comprise a difficult job to make everything fit, but information technology's important that everything fits in nicely and that no wires are pinched or jammed in too tightly thusly to avoid any harm to the conductors, potentially causing a short circuit train.

When the remote receiver is installed and the canopy and trim ring are back in place, we can now gain our changes in the multi-gang switch box.

In this facility, the deuce switches that controlled the fan/light source are in a 3-gang box that besides has the switch for the switched receptacles in the room. Take the faceplate and the gimmick screws and determine that the switch that controlled the light has a red wire on one terminal, and the switch that contained the devotee has a black electrify on one side of it. Both switches will have a black hot wire from the same unpleasant splice affiliated to each switch. We want to remove the switch we no longer need, and cap off the wires with wire nuts. We are abandoning the red wire present as we did in the winnow outlet. We wish use the remaining switch as a master control for the inaccessible receiver. I will move the switch we are still victimisation to the midway position, keep the switch for the room's receptacles in the first position, and then purpose a blank filler plate to fill the position of the swop we removed.

With the switches back in place, and the faceplate installed, it's meter to check our installation.

Restore power to the lap and then turn along the master turn on the bulwark. The remote should now control the operation of the rooter and the light. The fan speed and steering testament take up to be set to the desired position using the pull-mountain chain and reverse switch, and the light kit out pull-chain will have to beryllium on arsenic wellspring in arrange for the outback to work.

Changing a ceiling fan to remote ascendence is an first-class solvent for many applications, simply especially in a chamber where the interchange is aside the entrance room access. You can continue the remote on the bedside table, and have access to the light and the fan if needed in the middle of the night, without getting out of bed!

If you aren't comfortable and confident in safely completing a project like this on your possess, use the box on the left of the page to detect a tried and true trusted licensed electrician in your local area.

By Terry Peterman, The Cyberspace Electrician®

Can You Add a Remote Control to a Ceiling Fan?

Source: https://www.electrical-online.com/converting-an-existing-ceiling-fan-to-a-remote-control/